For Bosch Rexroth hydraulic and fan systems. Works with the TEXA Navigator. This is an 8 pin diagnostic cable used to connect the TEXA Navigator adapter to Bosch REXROTH cooling systems on various buses.
3-connector 6 pin / 9 pin / 12 pin terminal (OBDI) cable. For North American commercial vehicles. Works with the TEXA Navigator. This is a diagnostic cable used to connect the TEXA Navigator adapter to North American trucks. This is the standard cable used in commercial trucks. It has the 6 pin, 9 pin, and OBDI (pre-OBDII) cable. This cable is 2016 compliant, so commercial trucks with the "green" dash connector will work with this cable. This cable replaces the need for 3151/T16.
For First Generation ZF transmissions. Works with the TEXA Navigator. This is a 6 pin diagnostic cable used to connect the TEXA Navigator adapter to 1st generation ZF transmissions. This includes 6HP260, Ecolife, Ecomat 1 & 2, and Ergo Power transmissions found on various trucks and buses.
For Second Generation ZF transmissions. Works with the TEXA Navigator. This is a 9 pin diagnostic cable used to connect the TEXA Navigator adapter to 2nd generation ZF transmissions found on various buses and trucks. 2nd generation 8HP products were released starting in 2014. Efficiency improvements over the original design include a wider ratio spread of 7.8:1, reduced drag torque from the shift elements, reduction in required oil pump pressure, and broadened use of the coasting and start-stop systems.
For Kamaz, Solaris, Van Hool and Temsa vehicles. Works with the TEXA Navigator. This is a 9 pin diagnostic cable used to connect the TEXA Navigator adapter to Kamaz, Solaris, Van Hool and Temsa trucks and buses. Once the connection is made you will be able to diagnose and run dealer commands on your engine, transmission, suspension and ABS.
For coach buses with Voith systems. Works with the TEXA Navigator. This is a 4 pin diagnostic cable used to connect the TEXA Navigator adapter to coach buses with Voith retarders and Webasto heaters.
For Euro 2 and Euro 3 model DAF trucks. Works with the TEXA Navigator. This is a 16 pin diagnostic cable used to connect the TEXA Navigator adapter to Euro 2 and Euro 3 model DAF Trucks. Once the connection is made you will be able to diagnose and run dealer commands on your engine, transmission and ABS.
For Eberspacher heating systems on Solaris and Temsa buses. Works with the TEXA Navigator. This is an 8 pin diagnostic cable used to connect the TEXA Navigator adapter to Eberspacher auxiliary heating system mainly on Solaris and Temsa buses. Once the connection is made you will be able to diagnose and run dealer commands on your heating system.
For Euro 2 and 3 Mercedes trucks. Works with TEXA Navigator adapters. This is a diagnostic cable used to connect your TEXA Navigator to Euro 2 and Euro 3 Mercedes trucks. this T4 pin cable is mainly used on Mercedes Benz Light vehicles, such as the Sprinter I and II, but can also be used on other vehicles with a Mercedes-derived engine.
For Haldex EB+ modules. Works with the TEXA Navigator. This is a 4 pin diagnostic cable used to connect the TEXA Navigator adapter to Haldex EB+ modules on trailers. The EB+ is the newest generation of electronic braking systems from Haldex, this cable will allow you to plug directly into the EBS and run dealer tests and commands. Note: This cable requires the TEXA Power Supply and Adapter Kit for use with the Navigator TXT adapter.
For Iveco FPT engines. Works with the TEXA Navigator. This is an 30 pin to 19 pin diagnostic cable adapter used to connect the TEXA Navigator adapter to Iveco FPT engines. This adapter is to be used in conjunction with the Iveco FPT Industrial Cable.
For Iveco FPT engines. Works with the TEXA Navigator. This is a 30 pin diagnostic cable used to connect the TEXA Navigator adapter to Iveco FPT engines. Once the connection is made you will be able to diagnose and run dealer commands on your engine, transmission and ABS. In some instances, you will also need the Iveco FPT Engines Adapter.
For Euro 2 and Euro 3 Scania trucks. Works with the TEXA Navigator. This is a 16 pin diagnostic cable used to connect the TEXA Navigator adapter to Euro 2 and Euro 3 model Scania trucks. Once the connection is made you will be able to diagnose and run dealer commands on your engine, transmission and ABS.
For Thermoking refrigeration units. Works with the TEXA Navigator. This is a 15 pin diagnostic cable used to connect the TEXA Navigator adapter to Carrier Vectror and Thermoking refrigeration systems on various trailers and semitrailers.
Converts 7-way trailer connection to a standard 9 pin connection. Works with the TEXA Navigator. When connecting to trailers, you often need to connect directly to the trailer 7-way plug. This cable will allow you turn that trailer 7-way connection to a standard 9 pin connection so that you can connect directly to the trailer. This is the only PLC adapter that will work with the TEXA software.
For Volvo vehicles. Works with the TEXA Navigator. This is an 8 pin diagnostic cable used to connect the TEXA Navigator adapter to Volvo trucks (except new Euro 6 models).
For Volvo vehicles with Penta 1 Series engines. Works with the TEXA Navigator. This is a 2 pin diagnostic cable used to connect the TEXA Navigator adapter to Volvo Penta 1 Series engines. Once the connection is made you will be able to diagnose and run dealer commands on your engine, transmission and ABS.
For Volvo vehicles with Penta 2 Series engines. Includes 8 pin adapter cable (adapter number 16) Works with the TEXA Navigator. This is a diagnostic cable used to connect the TEXA Navigator adapter to Volvo Penta 2 Series engines. Once the connection is made you will be able to diagnose and run dealer commands on your engine, transmission and ABS. Note: This cable requires the TEXA Power Supply and Adapter Kit for use with the Navigator TXT adapter.
For Wabco and Knorr ABS / EBS systems. Works with the TEXA Navigator. This is a 7 pin diagnostic cable used to connect the TEXA Navigator adapter to Wabco and Knorr trailers for the diagnosis of the EBS, ABS, and suspension system. The TEXA system gives you full dealer capabilities on all ABS modules, on top of the engine and transmission. If you are looking to diagnose your Wabco or Knorr ABS/EBS modules that use the round 7 pin diagnostic port then this is the cable you will need. Once connected to your ABS/EBS your TEXA system will give you the dealer access you need to run tests and commands to diagnose your vehicle/trailer.
For Webasto heating heater systems on Temsa vehicles. Works with the TEXA Navigator. This is a 7 pin diagnostic cable used to connect the TEXA Navigator adapter to Webasto / Spheros heating systems in Temsa buses. Once the connection is made you will be able to diagnose and run dealer commands on your heating system.
LED-760 is a 4x6 style LED work light. 6 x Osram P9 LED's at 10 watt each, 4800 effective lumens, 5200-5500k, and only 3.8 amp/46 watt use. Select the light beam type, then select the bracket you need for your application. Includes a 5" adapter cable that fits 9005 or H11 connectors. You can find more adapter cables at the bottom or right side of this page. This is an updated model of our LED-660.
High power PAR-36 size replacement LED light for the old style sealed beam halogen light. 6 x 5 watt CREE LED chips. Actual power use is around 22 watt, effective lumen around 1700. 40° beam. Note: It is a good practice to drill a few holes on top and bottom of the housing the light is mounted in, this will help the lights cool.
High power PAR-36 size replacement LED light for the old style sealed beam halogen light. 6 x 5 watt CREE LED chips. Actual power use is around 22 watt, effective lumen around 1700. 60° Flood Beam. Note: It is a good practice to drill a few holes on top and bottom of the housing the light is mounted in, this will help the lights cool.
High power PAR-36 size replacement LED light for the old style sealed beam halogen light. 6 x 5 watt CREE LED chips. Actual power use is around 22 watt, effective lumen around 1700 Hi-Lo Beam, 800 low beam. Note: It is a good practice to drill a few holes on top and bottom of the housing the light is mounted in, this will help the lights cool.
LED 2x5 LED light for the top front cab on the 7000-8000 series tractor, and front hood light on older JD’s, 55 and 60 series. 50° beam pattern. 1700 effective lumen.
Cab lights for the 9000 series JD combine using a rectangular light on the cab - fits any vehicle using the JD9000 series cab. Use the combo beam for most distance, we suggest 2 combo beam and 4 flood beam for the combines.